Batteries13 listed
- Approved models
- 11
- Usable capacity
- 4.9-42.8 kWh
- Chemistry
- LFP
Redback Technologies · manufacturer profile
The SH-G3 hybrids and the R1, R2 and RED-P1 batteries
Inverter manufacturer
Updated 2 November 2026 · Checked against Redback's Australian warranties and datasheets, the CEC register (16 November 2026) and Synergy's list (30 October 2026) · By Solar Battery Perth
In short
Redback is a Queensland company that designs hybrid battery systems. Its G3 pairs an SH hybrid inverter with an enclosure of up to four 4.8 kWh units. The RED-R1, RED-R2 and RED-P1 batteries run on a separate inverter, and their units keep 10 years of warranty only while online through Redback's monitoring. A warranty claim ends up with Redback's own company in Salisbury, Queensland. A battery system needs an inverter with a battery-storage (DER-Storage) listing on Synergy's Supported Solutions List to be eligible for the WA Battery Scheme. Other scheme conditions apply. The SH5000-G3 and SH6000-G3 hybrids are on Synergy's list dated 30 October 2026, so an SH-G3-BE on either pairs with an inverter listed for battery storage on Synergy's list.
Specifications and pricing change. Confirm them with the manufacturer.
The company
Redback says it began as a handful of clean-tech enthusiasts and has been a dedicated team since 2015, with its headquarters in Brisbane. It says its design and engineering are focused on Australian homes. It says its generation-3 hybrid systems launched in 2025.
Redback designs the system and the inverter, and buys the battery units in. Redback says it stopped using LG batteries in 2019 and now uses Pylontech batteries in all of its battery systems. The SH6000-G3 datasheet lists the G3 enclosure's battery unit as the US5000, which is a Pylontech code on the Clean Energy Council (CEC) register. The R1, R2 and P1 datasheets name no cell maker.
In Australia, two Redback companies share one address in Salisbury, Queensland. Both are on the warranties. Redback Energy Pty Ltd is on the battery warranty and the three-phase hybrid warranty. Redback Operations Pty Ltd is on the SH-G3 hybrid warranty. It is also named as importer, with Luceo Australia Pty Ltd. Redback says its install partners cover Australia and New Zealand. No Redback document we read names a WA distributor.
A warranty claim goes to your installer first. The warranty documents give a claims email for Redback. The contact page gives a support line and email.
From Redback's contact page and the warranty contact block, read 29 October 2026.
The G3 arrives as one system rather than parts. Redback says the switchgear comes pre-wired, with a remote meter check, a CT flip and Smart Load Control as standard. It says a "stealth" install option leaves little cabling in view. It says the system connects by Wi-Fi, Bluetooth or Ethernet, with 4G as an option, and runs from a web portal or the Redback App. Those claims come from Redback's home page, not a datasheet, so they stay Redback's word.
The other difference is who stands behind it. Both companies on the warranties are Redback's own, at one address in Queensland. The battery units inside come from Pylontech. So a G3 owner has an Australian company on the warranty and a battery maker's cells inside.
The thing to know before a quote is the online condition. The R1, R2 and RED-P1 battery units carry 10 years while the system stays connected to the internet through Redback's monitoring. Offline, it is five years. The SH-G3 hybrids and their enclosure carry 10 years with no online condition on the term, though their warranty also excludes loss caused by a lost cloud connection.
Three Redback battery lines and four hybrid inverter lines are on the Clean Energy Council (CEC) register. The batteries are listed until 31 December 2027. The hybrids are listed to dates in February, September and October 2029. The SH-G3 enclosure has no row of its own under Redback. Its US5000 units are listed under Pylontech. Redback's SI inverters are on the register for solar only.
SH5000-G3 or SH6000-G3 hybrid with an enclosure of up to four 4.8 kWh units, 19.2 kWh nominal
Inverters CEC approved; battery units listed under Pylontech
16 kWh nominal, 15.2 kWh usable, IP65, outdoors
CEC approved
5.12 kWh nominal, 4.864 kWh usable, IP20, indoors
CEC approved
High-voltage stacks of 13.3, 19.95, 26.6 or 33.25 kWh usable, IP54
CEC approved
Single-phase high-voltage hybrid, 5 to 10 kW, four MPPTs
CEC approved
Single-phase and three-phase high-voltage hybrids
CEC approved
No Australian date or approval in what we read
Coming, Redback says
Redback sells the G3 as two parts together: an SH-G3 hybrid inverter and a battery enclosure. A hybrid inverter runs the solar panels, the battery and the house from one box. The SH5000-G3 puts out 5 kW and the SH6000-G3 6 kW. The enclosure, the SH-G3-BE, holds up to four 4.8 kWh units, 19.2 kWh nominal in all. The datasheet prints no usable figure for the enclosure, so this page does not either. The two hybrids are on the Clean Energy Council's inverter register. There's no Redback G3 battery on the CEC battery list as of 20 October 2026. The US5000 units inside the enclosure are listed under Pylontech, to 31 December 2027.
In a blackout the backup port carries the circuits wired to it. It is rated 5,000 VA on the SH5000-G3 and 6,000 VA on the SH6000-G3 (VA is the rating the datasheet uses for backup output). Each can run higher for 60 seconds, 7,000 and 8,000 VA, which covers a motor starting.
Each hybrid has two MPPTs (the trackers that get the most out of each string of panels), so two roof faces can work apart. The SH5000-G3 takes up to 8 kWp of panels and the SH6000-G3 up to 9.6 kWp (kilowatts peak, the panels' combined rated output). The inverter runs from -25 to 60 °C and lowers its output below 10 °C and above 45 °C.
The inverter is rated IP66, which means dust-tight and sealed against strong water jets. The enclosure is IP54, dust-protected and protected against splashing water. Redback says the G3 is for outdoor installation. Redback's home page also says the G3 reaches 51.2 kWh of storage. The datasheet gives the enclosure 19.2 kWh, and no document we read says how many enclosures one SH-G3 takes. So this page stops at 19.2 kWh.
Both are single low-voltage batteries that run on a separate inverter. The RED-R1-5000LV holds 5.12 kWh nominal and 4.864 kWh usable, at 95% depth of discharge (the share of the battery the system lets you use). It puts out 2.56 kW, weighs 44 kg and is rated IP20, so it lives indoors. Its datasheet gives 6,000 cycles at 25 °C.
The RED-R2-16KLV is the newer and larger of the two, approved in July 2026. It holds 16 kWh nominal and 15.2 kWh usable, puts out 4.6 kW, and is rated IP65 for outdoor use. It stands 970 mm tall, 413 mm wide and 243 mm deep, weighs 127 kg and cools itself without a fan. It charges from 5 to 55 °C and discharges from -20 to 55 °C. The current is cut back when the cells sit outside their working range.
Neither battery comes with an inverter named for it. Redback's pairing statement for the R2 is a scanned PDF with no text, so we could not read it. The quote has to name the inverter, and the installer has to confirm the pairing in writing.
The RED-P1 enclosures are Redback's high-voltage stacks for bigger homes. Two, three, four or five RED-P1-7000HV units give 14, 21, 28 or 35 kWh nominal. Usable is 13.3, 19.95, 26.6 or 33.25 kWh at 95% depth of discharge. Power rises with the stack, from 7.04 kW to 17.6 kW. The enclosures are rated IP54.
Redback's high-voltage hybrids come in three families. The single-phase RED-H4 runs from 5 to 10 kW with four MPPTs, one string each. Its largest model takes up to 20 kWp of panels. It is rated IP66, runs from -40 to 60 °C and lowers its output above 45 °C. The single-phase RED-H3-S has three MPPTs and is also rated IP66. The RED-H3-T is the three-phase family, from 10 to 30 kW.
The RED-H4 datasheet says it takes an LFP battery at 350 to 550 V DC (LFP is lithium iron phosphate, the cell type in every Redback battery on the register). That is a voltage window, not a pairing. Redback's installation manual for its three-phase high-voltage system pairs the RED-P1 enclosures with the RED-H3-T. Each inverter takes up to two BE14HV or BE21HV enclosures. It takes only one BE28HV or BE35HV. No Redback document we read pairs a RED-P1 with a single-phase hybrid.
The SH-G3-BE enclosure pairs with the SH5000-G3 and SH6000-G3. Both the datasheet and the hybrid warranty document it with those two. No Redback document we could read pairs the RED-R1 or RED-R2 with a named inverter, because those pairing statements have no text layer. Ask for the exact inverter code on the quote and Redback's written confirmation of the pairing.
Every Redback battery on the register uses LFP cells. The R2 and the RED-P1 enclosures are listed for outdoor use, and the R1 is not. No test report we read goes further than that, so this page does not either.
The hybrids carry 10 years. For the SH-G3 and the RED-H3-T it ends at the earlier of 10 years from install or 11 years from manufacture. The network adaptors and energy meters that come with them get two years. Both terms apply to units made on or after 1 April 2025 and installed in Australia by an accredited installer. The Redback documents we read disagree on the RED-H3-S and RED-H4. Their warranty sets no internet condition, while their datasheets print the term with an internet condition (5 or 10 years on the RED-H3-S, 10 years on the RED-H4).
The batteries have one condition that matters. The RED-R1, RED-R2 and the RED-P1-7000HV units carry 10 years while the system stays connected to the internet through Redback's monitoring. Offline, it is five years. The 10 years also ends at the earlier of 10 years from install or 11 years from manufacture. The warranty excludes loss caused by failing to keep a stable connection to Redback's cloud.
The capacity promise is that the battery loses no more than 30% in 10 years. The clock starts at the earlier of install or manufacture. It also runs until 3.65 MWh (3,650 kWh) of energy has passed through per usable kWh, whichever comes later, subject to the warranty's conditions. That allowance covers one full cycle a day for all 10 years.
A RED-P1 system sits under two documents. The enclosure warranty names the four RED-P1 enclosure codes, with no online condition on the term and no capacity clause (it keeps the cloud-connection exclusion). The battery warranty names the RED-P1-7000HV units inside, with both. No Redback document we read says which warranty applies to the system as a whole. So a RED-P1 quote needs Redback's written answer first.
A claim starts with the installer. The warranty documents give warranty@redbacktech.com for Redback. They name Redback Operations Pty Ltd and Luceo Australia Pty Ltd as importers. Ask the installer to show the system online in the Redback app before they leave. An offline R1, R2 or RED-P1 unit carries five years rather than ten.
Showing: Western Australia, Synergy network. Other states: not covered yet
A battery system needs an inverter with a battery-storage (DER-Storage) listing on Synergy's Supported Solutions List to be eligible for the WA Battery Scheme. Other scheme conditions apply. The SH5000-G3 and SH6000-G3 hybrids are on Synergy's list dated 30 October 2026, so an SH-G3-BE on either pairs with an inverter listed for battery storage on Synergy's list.
Synergy's list names inverters, not batteries, so a Redback battery counts through the hybrid it runs on. The line above names the SH-G3 hybrids the list carries today. An R1, R2 or RED-P1 quote names its own inverter. That inverter's exact code is the one that counts. Our inverter library badges each model Synergy lists for the scheme.
Redback's inverters on Synergy's list are not yet marked activation-ready for a Synergy VPP program (list dated 30 October 2026). The WA scheme also asks the household to join a virtual power plant (VPP), a program that lets a retailer draw on home batteries. Synergy's own VPP is Battery Rewards. The scheme also accepts an alternative VPP from the battery supplier, under its own conditions.
Everything else the scheme asks for is set out on our WA battery rebate page. Our Synergy approved products guide explains what the list covers.
Redback says its next system is the G4, with the inverter, battery, power conversion and energy management in one unit. It says each battery module has its own DC-DC optimiser, so the stack grows module by module. It says backup is built in, the cells are 314 Ah and the unit is rated IP66. Its About page says generation 4 is coming in 2026. No Redback document we read gives the G4 an Australian date, datasheet or approval. So treat it as coming and to be confirmed.
Redback sells one system that arrives whole, the G3, and a set of batteries and hybrids that an installer puts together. The G3 goes outdoors and its enclosure holds up to 19.2 kWh nominal. An R2 goes outdoors on its own and an R1 lives inside. A RED-P1 stack reaches 33.25 kWh usable. The R1, R2 and RED-P1 battery units keep their 10 years only while online, so the internet link at the battery is part of the install. A battery system needs an inverter with a battery-storage (DER-Storage) listing on Synergy's Supported Solutions List to be eligible for the WA Battery Scheme. Other scheme conditions apply. The SH5000-G3 and SH6000-G3 hybrids are on Synergy's list dated 30 October 2026, so an SH-G3-BE on either pairs with an inverter listed for battery storage on Synergy's list.
Ask the installer for the exact inverter and battery model codes. If the quote is for an R1, R2 or RED-P1, ask for Redback's written pairing confirmation.
Solar Battery Perth is independent. We're not owned by an energy retailer or a manufacturer. Installers quote the actual price.
For checking
| Batteries | LFP (lithium iron phosphate), 4.9-42.8 kWh usable |
|---|---|
| Approved now | 11 batteries and 23 inverters on the CEC (Clean Energy Council) register |
| Support in Australia | Office and phone line. Contact details |
| CEC listings | 34 approved right now · 13 delistedApproved |
| Documents |
Each product type at a glance. The full lists, grouped by series, are below.
We haven't reviewed Redback Technologies inverters in depth yet. We don't hold warranty terms or a series review for them, so confirm those with your installer. Compare inverters from other brands
Pick a type to open its full list, grouped by series.
Grouped by series. Open a series for each variant, or a model for full specs.
11 CEC-approved batteries, 2 not currently listed · grouped into 4 series
Grouped by series. Open a series for each variant, or a model for full specs.
23 CEC-approved inverters, 11 not currently listed · grouped into 12 series
SI10000 (AS4777-2 2020)
SI5000 (AS4777-2 2020)
SI6000 (AS4777-2 2020)
SI8000 (AS4777-2 2020)
SI10000 (AS4777-2 2020)
SI5000 (AS4777-2 2020)
SI6000 (AS4777-2 2020)
SI8000 (AS4777-2 2020)
What has happened to Redback Technologies on the CEC register.
Each block is one register event. Tap a year to see its events in the list below.
Smart Hybrid System Launch
All-in-one hybrid inverter and battery system launched
ACCC recall: ESS Home Energy Storage System Batteries
The affected batteries may overheat and catch fire without warning. A fire could cause injury, death or property damage. A house in Victoria was completely destroyed.
ACCC recall update: ESS Home Energy Storage System Batteries
Status: still active
⚡ 20 Inverter Models Listed
Inverter range expanded to 20 CEC-approved models.
For the full warranty, yes. The RED-R1, RED-R2 and the RED-P1-7000HV units carry 10 years while connected to the internet through Redback's monitoring, and five years if not. The SH-G3 hybrids and their enclosure have no online condition on the term, though their warranty also excludes loss caused by a lost cloud connection.
Your installer first. The warranty documents name Redback Energy Pty Ltd and Redback Operations Pty Ltd in Salisbury, Queensland, and give warranty@redbacktech.com for claims. Redback's support line is in the Support in Australia section above.
The G3 is sold for outdoor installation, Redback says, with an IP66 inverter and an IP54 enclosure. The RED-R2 is rated IP65 and listed for outdoor use. The RED-R1 is IP20 and listed for indoors. The inverters lower their output above 45 °C. Redback's install manuals for the G3 and the RED-P1 list full-sun locations, and exposed spots where wind-driven rain may get into the enclosure, as not suitable, and say an install against those limits may void the warranty.
The warranties Redback publishes name its own Australian companies. The battery warranty, effective 1 June 2026, names Redback Energy Pty Ltd, at 172 Evans Road, Salisbury, Queensland, as the warranty provider. The SH-G3 hybrid warranty, effective 9 February 2026, names Redback Operations Pty Ltd. A claim starts with your installer, and the warranty documents give warranty@redbacktech.com for Redback.
Redback Technologies is headquartered in Brisbane, Australia. Its products are sold in Australia through SAA-accredited installers.
Redback Technologies's home batteries use LFP cells. LFP (lithium iron phosphate) is the most common residential chemistry in WA for its long cycle life and stability in Perth's heat.
Solar Battery Perth lists 11 CEC-approved Redback Technologies battery models with specs, indicative pricing and warranty detail. Compare them against other brands to find the best fit for your Perth home.
Redback Technologies has 23 CEC-approved inverter models from 5-125 kW (single and three phase). Compare them against other brands by size, phase and battery compatibility.
Are you Redback Technologies?
Help us keep this profile up to date.
How the WA Battery Scheme works, and why eligibility follows the inverter on the quote.
What Synergy's Supported Solutions List covers, and how our inverter library shows which models are on it.
Every notice we track.
The maker of the batteries inside the G3.
Get a quote from a member installer who covers your area. You choose whether to act on it. No obligation.
Product specifications, pricing, and availability are subject to change without notice. We make no warranties regarding product performance, longevity, or suitability for your specific needs.
Always verify specifications with the manufacturer and installer before purchase. Warranty terms are set by manufacturers and may have conditions not disclosed here. Battery performance degrades over time.