Batteries72 listed
- Approved models
- 60
- Usable capacity
- 4.7-49.1 kWh
- Pair with an inverter listed for battery storage on Synergy's list
- 12 of 72 systems
- Chemistry
- LFP
FoxESS · manufacturer profile
The CQ7 and EQ5500 stacks and the Fox inverters they run on
Solar manufacturer
Updated 2 November 2026 · Checked against Fox ESS's Australian datasheets, compatibility declarations and warranty policy, the CEC register (16 November 2026) and Synergy's list (30 October 2026) · By Solar Battery Perth
In short
Fox ESS makes hybrid inverters and the batteries that run on them. Its two stackable home batteries, the CQ7 and EQ5500, run only on Fox inverters. The CQ7 and the EQ5500 are stacks of lithium iron phosphate modules. The CQ7 starts at 13.92 kWh with two modules and can run 9.22 kW at once, up to the inverter's rating. The EQ5500 starts at 10.92 kWh and grows in 5.46 kWh steps. Both carry a 10-year warranty that depends on registering the system with Fox when it is switched on. FoxESS Australia Pty Ltd in Springvale, Victoria, is the importer behind that warranty, and a claim reaches it through the installer. A battery system needs an inverter with a battery-storage (DER-Storage) listing on Synergy's Supported Solutions List to be eligible for the WA Battery Scheme. Other scheme conditions apply. Fox's H1-G2, AC1-G2, KH, KA, H3 Smart and H3 Pro inverters, which a CQ7 or EQ5500 runs on, were on Synergy's list dated 30 October 2026. A CQ7 or EQ5500 on one of them pairs with an inverter listed for battery storage on Synergy's list.
Specifications and pricing change. Confirm them with the manufacturer.
The company
Fox ESS was founded in Wenzhou, China, in September 2019, and it makes inverters and batteries. The company is not listed on a stock exchange. It lodged an application to list in Shenzhen in June 2025, and we have not seen the outcome.
In Australia it sells through FoxESS Australia Pty Ltd, a wholly owned subsidiary in Springvale, Victoria. That company is the importer named in the battery warranty. So a warranty claim has an Australian company behind it. The older 1K5-BAT-4660 warranty prints an earlier Box Hill address for the same company.
A warranty claim goes through your installer, or someone Fox authorises, rather than through you. The installer reports the fault to Fox with the model, fault code and fault details. Fox tests it, issues a ticket, and approves and sends a replacement within three working days when stock allows. The faulty unit goes back within 30 days.
From the Fox ESS Australia and New Zealand battery warranty policy, version 2.7, read 8 October 2026.
The battery and the inverter come as a set. Fox's compatibility declarations pair the CQ7 and the EQ5500 only with Fox inverters, and each closes by saying every model named is a Fox product. So the inverter on the quote decides whether either battery can go in.
There are two ways in. A Fox hybrid inverter runs the solar panels and the battery together. The H1-G2 and KH are the single-phase hybrids, and the H3 Smart and H3 Pro the three-phase ones. A home keeping another brand's solar inverter uses a Fox battery inverter instead. The AC1-G2 and KA are registered as battery-only inverters. They run a Fox battery beside the solar inverter already on the wall. In WA, adding a battery to an existing solar system counts as an alteration and can trigger whole-of-site compliance, so compare an AC-coupled retrofit against replacing your inverter with a hybrid. For many existing systems the sound path is replacing toward a DC-coupled / hybrid-inverter setup rather than expanding an AC-coupled one, avoiding future compliance limitations.
Every kilowatt-hour on the label is usable. Fox rates both batteries at 100% depth of discharge, the share of the battery you are allowed to drain. And a stack can grow after installation. The manuals allow a module to be added to an installed stack, under conditions the installer manages on the day.
Fox's battery lines and inverters are on the Clean Energy Council (CEC) register in our 20 October 2026 snapshot. The CQ7 was approved on 18 May 2026 and the EQ5500 on 16 June 2026, both listed to 31 December 2027. The EP12 Plus (w) joined in June 2026. The Power Cube (PQ1 with EQ5500-S modules) was approved on 20 October 2026 and is listed to 31 December 2027. The earlier lines stay on the register beside them. The ECS2900 and ECS4800 joined in January 2024, the EP5 and EP11 in June 2024 and the EQ4800 in November 2024. The 1K5-BAT-4660 followed in May 2025 and the CQ6 in December 2025. The ECS listings run to 2 January 2027.
Stacks of 6.96 kWh LFP modules, IP65, 100% depth of discharge. The register also lists a (w) version, with a warm-up function that charges down to -25°C, and the lower-current CQ7-50, which has no datasheet of its own
Standalone battery, on a separate inverter. On the CEC register: 13.92 to 97.44 kWh usable, in 6.96 kWh steps (2 to 14 modules)
CEC approved
Stacks of 5.46 kWh modules, 10.92 to 49.14 kWh, floor-mounted, IP65
CEC approved
The earlier stack, 11.98 to 83.86 kWh, with a 12-year warranty
CEC approved
Stacks from 9.32 to 41.93 kWh
CEC approved
Single units that their datasheets put at 5.18, 10.36 and 11.52 kWh, with up to four in parallel
CEC approved
The older lines, rated at 90% depth of discharge
CEC approved, listed to 2 January 2027
Stacks of 4.66 kWh modules, with a warranty of its own
CEC approved
H1-G2 and KH hybrids and the AC1-G2 and KA battery inverters on single-phase; H3 Smart, H3 Pro and H3 Plus on three-phase
CEC approved
The CQ7 is a stack of 6.96 kWh LFP (lithium iron phosphate) modules. On a single-phase supply (the standard household supply) it runs from two modules, 13.92 kWh, to seven, 48.72 kWh. Seven is the most a single-phase Fox hybrid accepts. Bigger stacks exist, up to fourteen modules and 97.44 kWh, but only Fox's three-phase inverters take them (three-phase is the heavier supply some larger homes have).
Power rises with every module. Two modules supply 9.22 kW and seven supply 32.26 kW. Power is how much the battery can run at once, and the inverter still caps what reaches the house. Fox's single-phase hybrids run from 3 kW to 10.5 kW, so a 6 kW hybrid passes at most 6 kW whatever the stack can do.
The stack stands on four adjustable feet on level ground, 20 mm from a wall, and is fixed to that wall with two brackets. Past six modules the manual adds a second pair of brackets in the middle layer, so the taller stacks take four. Every height has the same 660 by 360 mm footprint. Two modules stand 420 mm tall and weigh 105.5 kg; seven stand 1,195 mm and weigh 358 kg. It is rated IP65 (dust-tight and protected against water jets), and the datasheet allows it outdoors or indoors on its stand.
It charges between 0°C and 55°C and discharges from -10°C. The (w) version adds a warm-up function that lets it charge down to -25°C. The manual rates the cells at 6,000 cycles or more at 25°C, measured down to 70% of capacity. The datasheet gives a round-trip efficiency above 95%, the share of stored energy that comes back out. Neither is a warranty term.
A module can be added to an installed stack. The new module has to sit within 0.5 V of the existing ones and should have been charged within the last five months. The stack should be at about half charge when it goes in. Those are the installer's job, but they explain why an added module is not an off-the-shelf swap.
The EQ5500 is the smaller-step stack. Its modules hold 5.46 kWh each, so it runs from 10.92 kWh with two modules to 49.14 kWh with nine. Nine is the limit on either kind of supply. Power runs from 4.48 kW with two modules to 20.16 kW with nine, and the inverter caps what reaches the house in the same way.
It stands on the floor 20 mm from a wall, fixed with two brackets through the modules. Past six modules the manual adds a second pair of brackets in the middle layer, so the taller stacks take four. The manual asks for a hard, level floor, sheltered from direct sunlight, rain and snow. Its footprint is 570 by 380 mm. Two modules stand 386 mm tall and weigh 85 kg; nine stand 1,352 mm and weigh 372 kg. It is rated IP65, and the datasheet lists it for floor mounting outdoors or indoors.
It uses LFP cells, charges between 0°C and 55°C, and gives a round-trip efficiency above 95%. Neither the datasheet nor the manual prints a cycle rating, so this page has none. Fox's EQ5500 compatibility list says its optional fire-suppression module is not sold in Australia, though the Australian manual describes one in each unit. Ask the installer which applies. Adding a module follows the same rules as the CQ7.
Only a Fox one. The CQ7 takes two to seven modules on the single-phase H1-G2 and AC1-G2 (3 to 6 kW) and KH and KA (7 to 10.5 kW). On three-phase, the H3 Smart (5 to 15 kW) and H3 Pro (15 to 30 kW) take up to twelve per battery input. The H3 Pro has two inputs. Fox's April 2026 declaration starts both at three modules, while its September compatibility list starts the H3 Smart at two and the H3 Pro at four. The installer confirms the minimum. The H3 Plus (50 to 125 kW) takes up to three stacks of four to fourteen, which is commercial territory.
The EQ5500 takes two to nine modules on the same single-phase inverters. The H3 Smart takes three to nine, and the H3 Pro three to nine on each of up to two battery inputs. The AC1-G2 and KA on those lists are the battery inverters, so a home keeping another brand's solar inverter has a route to either battery. In WA, adding a battery to an existing solar system counts as an alteration and can trigger whole-of-site compliance, so compare an AC-coupled retrofit against replacing your inverter with a hybrid. For many existing systems the sound path is replacing toward a DC-coupled / hybrid-inverter setup rather than expanding an AC-coupled one, avoiding future compliance limitations.
The CQ7 and EQ5500 both use LFP cells and carry an IP65 rating. The CQ7 manual says each battery unit carries an aerosol fire-suppression module that triggers by heat. The CQ7 datasheet lists a fire protection function. Fox's documents disagree on the EQ5500. Its Australian manual describes the same module in each unit. Its compatibility list calls the module optional and not sold in Australia. Neither datasheet gives a backup switchover time (how fast the battery takes over in a blackout).
Both batteries carry 10 years from installation, with at least 70% of capacity promised at the end. The promise also ends once a set amount of energy has passed through the battery, whichever comes first. The term is 120 months from installation and no more than 125 months from the date of manufacture. So a battery that sat in a warehouse for more than five months gets less than the full 10 years.
The energy allowance is set per stack size. The smallest CQ7 stack carries 70.76 MWh (megawatt-hours, or 70,760 kWh), and the smallest EQ5500 stack 46.07 MWh. At one full cycle a day the 10 years arrive before the allowance on every size of either battery.
Registration is the main condition. The policy asks for the system to be registered on Fox's website and connected to it when it is commissioned. It allows up to 36 months and recommends six weeks, so the easy path is to have the installer do it on the day. The capacity promise also holds only while the air around the battery stays between -10°C and 50°C.
Two other lines turn up on quotes. A 12-year figure points to the older CQ6, which carries 144 months from installation, not to the CQ7. The 1K5-BAT-4660 has a policy of its own. It carries 60 months, plus another 60 if the product is registered within 36 months of manufacture. From the sixth year it needs an annual inspection by a Fox-authorised technician.
Claims go through the installer, or someone Fox authorises, as the Support section describes. The policy carries the Australian Consumer Law statement, and Fox's warranty sits on top of those rights.
The warranty answer is 10 years, with 70% of capacity promised for that long, unless the energy allowance runs out first. At one full cycle a day the allowance lasts the full 10 years on every CQ7 and EQ5500 size. The CQ7 manual adds a lab figure of 6,000 cycles or more at 25°C. The EQ5500 documents print no cycle figure.
Showing: Western Australia, Synergy network. Other states: not covered yet
A battery system needs an inverter with a battery-storage (DER-Storage) listing on Synergy's Supported Solutions List to be eligible for the WA Battery Scheme. Other scheme conditions apply. Fox's H1-G2, AC1-G2, KH, KA, H3 Smart and H3 Pro inverters, which a CQ7 or EQ5500 runs on, were on Synergy's list dated 30 October 2026. A CQ7 or EQ5500 on one of them pairs with an inverter listed for battery storage on Synergy's list.
Synergy's list names inverters, not batteries. A Fox battery counts through the Fox inverter on the quote, whether that is a hybrid or a battery inverter. The list names inverters model by model and changes over time, so the exact inverter model code on the quote is what to check against it.
Fox ESS's inverters on Synergy's list are not yet marked activation-ready for a Synergy VPP program (list dated 30 October 2026). To claim under the WA scheme, the home also joins a virtual power plant (VPP), a program that lets a retailer draw on home batteries. Synergy runs Battery Rewards. A VPP from the battery supplier can count instead, on terms of its own.
Everything else the scheme asks for sits on our WA battery rebate page, and our Synergy approved products guide explains how to read the list.
The CQ7 and EQ5500 run only with Fox inverters, so the battery and inverter come as a set. In a Perth home with a Fox hybrid, either battery stands on the floor beside it, fixed to the wall behind. The installer can add modules to the stack later. A home keeping another brand's solar inverter runs either battery through a Fox AC1-G2 or KA battery inverter instead. In WA, adding a battery to an existing solar system counts as an alteration and can trigger whole-of-site compliance, so compare an AC-coupled retrofit against replacing your inverter with a hybrid. For many existing systems the sound path is replacing toward a DC-coupled / hybrid-inverter setup rather than expanding an AC-coupled one, avoiding future compliance limitations. A battery system needs an inverter with a battery-storage (DER-Storage) listing on Synergy's Supported Solutions List to be eligible for the WA Battery Scheme. Other scheme conditions apply. Fox's H1-G2, AC1-G2, KH, KA, H3 Smart and H3 Pro inverters, which a CQ7 or EQ5500 runs on, were on Synergy's list dated 30 October 2026. A CQ7 or EQ5500 on one of them pairs with an inverter listed for battery storage on Synergy's list.
Ask the installer for the battery, the number of modules and the inverter, each by model code. Have the installer register the system on Fox's website on the day it is switched on. The installer's quote sets the price, and the module count, inverter and registration are the parts to check against this page.
Solar Battery Perth is independent. We're not owned by an energy retailer or a manufacturer. Installers quote the actual price.
For checking
| Warranty | 10 years on the CQ7 and EQ5500, with the system registered with Fox at commissioningFox ESS's Australian and New Zealand battery warranty policy, version 2.7 |
|---|---|
| Batteries | LFP (lithium iron phosphate), 4.7-49.1 kWh usable |
| Approved now | 60 batteries and 131 inverters on the CEC (Clean Energy Council) register |
| Support in Australia | Office. Contact details |
| Local support | Yes, support handled through Australian channelsSource: maker's Australian site, checked 6 May 2026Confirmed |
| CEC listings | 191 approved right now · 29 delistedApproved |
| Documents |
Each product type at a glance. The full lists, grouped by series, are below.
Pick a type to open its full list, grouped by series.
Grouped by series. Open a series for each variant, or a model for full specs.
60 CEC-approved batteries, 12 not currently listed · grouped into 12 series · showing first 50 of 58
The CEC lists each size of this product, paired with each inverter, as its own approval. Pick a size to see its full specs.
CEC model: CQ7-L2 · LFP
View seriesBased on manufacturer specifications and CEC-approved configurations. Always confirm system design with your installer.
Grouped by series. Open a series for each variant, or a model for full specs.
131 CEC-approved inverters, 17 not currently listed · grouped into 26 series · showing first 50 of 148
PQ1-10.0_EQ5500-S_2S (AS4777-2 2020)
PQ1-10.0_EQ5500-S_3S (AS4777-2 2020)
PQ1-10.0_EQ5500-S_4S (AS4777-2 2020)
PQ1-10.0_EQ5500-S_5S (AS4777-2 2020)
PQ1-10.0_EQ5500-S_6S (AS4777-2 2020)
PQ1-10.0_EQ5500-S_7S (AS4777-2 2020)
PQ1-10.0_EQ5500-S_8S (AS4777-2 2020)
PQ1-10.0_EQ5500-S_9S (AS4777-2 2020)
PQ1-12.0_EQ5500-S_2S (AS4777-2 2020)
PQ1-12.0_EQ5500-S_3S (AS4777-2 2020)
PQ1-12.0_EQ5500-S_4S (AS4777-2 2020)
PQ1-12.0_EQ5500-S_5S (AS4777-2 2020)
PQ1-12.0_EQ5500-S_6S (AS4777-2 2020)
PQ1-12.0_EQ5500-S_7S (AS4777-2 2020)
PQ1-12.0_EQ5500-S_8S (AS4777-2 2020)
PQ1-12.0_EQ5500-S_9S (AS4777-2 2020)
PQ1-5.0_EQ5500-S_2S (AS4777-2 2020)
PQ1-5.0_EQ5500-S_3S (AS4777-2 2020)
PQ1-5.0_EQ5500-S_4S (AS4777-2 2020)
PQ1-5.0_EQ5500-S_5S (AS4777-2 2020)
PQ1-5.0_EQ5500-S_6S (AS4777-2 2020)
PQ1-5.0_EQ5500-S_7S (AS4777-2 2020)
PQ1-5.0_EQ5500-S_8S (AS4777-2 2020)
PQ1-5.0_EQ5500-S_9S (AS4777-2 2020)
PQ1-8.0_EQ5500-S_2S (AS4777-2 2020)
PQ1-8.0_EQ5500-S_3S (AS4777-2 2020)
PQ1-8.0_EQ5500-S_4S (AS4777-2 2020)
PQ1-8.0_EQ5500-S_5S (AS4777-2 2020)
PQ1-8.0_EQ5500-S_6S (AS4777-2 2020)
PQ1-8.0_EQ5500-S_7S (AS4777-2 2020)
PQ1-8.0_EQ5500-S_8S (AS4777-2 2020)
PQ1-8.0_EQ5500-S_9S (AS4777-2 2020)
PQ3-10.0-L-M_EQ5500-S_2S (AS4777-2 2020)
PQ3-10.0-L-M_EQ5500-S_3S (AS4777-2 2020)
PQ3-10.0-L-M_EQ5500-S_4S (AS4777-2 2020)
PQ3-10.0-L-M_EQ5500-S_5S (AS4777-2 2020)
PQ3-10.0-L-M_EQ5500-S_6S (AS4777-2 2020)
PQ3-10.0-L-M_EQ5500-S_7S (AS4777-2 2020)
PQ3-10.0-L-M_EQ5500-S_8S (AS4777-2 2020)
PQ3-10.0-L-M_EQ5500-S_9S (AS4777-2 2020)
PQ3-15.0-M_EQ5500-S_2S (AS4777-2 2020)
PQ3-15.0-M_EQ5500-S_3S (AS4777-2 2020)
PQ3-15.0-M_EQ5500-S_4S (AS4777-2 2020)
PQ3-15.0-M_EQ5500-S_5S (AS4777-2 2020)
PQ3-15.0-M_EQ5500-S_6S (AS4777-2 2020)
PQ3-15.0-M_EQ5500-S_7S (AS4777-2 2020)
PQ3-15.0-M_EQ5500-S_8S (AS4777-2 2020)
PQ3-15.0-M_EQ5500-S_9S (AS4777-2 2020)
PQ3-5.0-M_EQ5500-S_2S (AS4777-2 2020)
PQ3-5.0-M_EQ5500-S_3S (AS4777-2 2020)
What has happened to FoxESS on the CEC register.
Each block is one register event. Tap a year to see its events in the list below.
ECS Battery Series Launch
Modular low-voltage battery system for residential applications
⚡ 20 Inverter Models Listed
Inverter range expanded to 20 CEC-approved models.
⚡ 50 Inverter Models Listed
Inverter range expanded to 50 CEC-approved models.
🔋 50 Battery Listings
Battery range expanded to 50 CEC-approved listings.
🔋 100 Battery Listings
Battery range expanded to 100 CEC-approved listings.
Not directly. Fox's declarations pair the CQ7 and EQ5500 only with Fox inverters. A home keeping another brand's solar inverter adds a Fox AC1-G2 or KA battery inverter. The register lists both as battery-only inverters. They run the battery beside the solar inverter already on the wall. In WA, adding a battery to an existing solar system counts as an alteration and can trigger whole-of-site compliance, so compare an AC-coupled retrofit against replacing your inverter with a hybrid. For many existing systems the sound path is replacing toward a DC-coupled / hybrid-inverter setup rather than expanding an AC-coupled one, avoiding future compliance limitations.
Through the installer. The manuals allow a module to be added to an installed CQ7 or EQ5500 stack. The new module has to sit within 0.5 V of the existing ones and should have been charged within the last five months, with the stack at about half charge. A single-phase CQ7 stops at seven modules, and an EQ5500 at nine.
The warranty requires the system to be connected to Fox's website when it is commissioned, and registration happens there. The CQ7 and EQ5500 manuals name the FoxCloud app and the FoxCloud web platform for owners.
The warranty promises 70% of capacity for 10 years, or until the energy allowance is used up. At one full cycle a day the 10 years arrive first on every CQ7 and EQ5500 size. The CQ7 manual rates the cells at 6,000 cycles or more in lab conditions.
Your installer, or someone Fox authorises. The installer reports the fault with the model and fault code. Fox tests it, and a replacement is approved within three working days when stock allows. The importer behind the policy is FoxESS Australia Pty Ltd in Springvale, Victoria.
Both the CQ7 and the EQ5500 are rated IP65 and listed for outdoor or indoor installation on their datasheets. Both manuals still ask for a spot sheltered from direct sunlight and rain, on a hard, level floor. The CQ7 manual recommends a rain canopy. The warranty's capacity promise holds only between -10°C and 50°C.
FoxESS's home batteries use LFP cells. LFP (lithium iron phosphate) is the most common residential chemistry in WA for its long cycle life and stability in Perth's heat.
Solar Battery Perth lists 60 CEC-approved FoxESS battery models with specs, indicative pricing and warranty detail. Compare them against other brands to find the best fit for your Perth home.
Are you FoxESS?
Help us keep this profile up to date.
How the WA Battery Scheme works, and why eligibility follows the inverter on the quote.
What Synergy's Supported Solutions List covers, and how our inverter library shows which models are on it.
How the inverter paired with a battery sets its charge rate, discharge rate and backup power.
Who to contact first when a home battery fails, and what records to keep.
Get a quote from a member installer who covers your area. You choose whether to act on it. No obligation.
Product specifications, pricing, and availability are subject to change without notice. We make no warranties regarding product performance, longevity, or suitability for your specific needs.
Always verify specifications with the manufacturer and installer before purchase. Warranty terms are set by manufacturers and may have conditions not disclosed here. Battery performance degrades over time.