Batteries15 listed
- Approved models
- 15
- Usable capacity
- 6.4-49.9 kWh
- Pair with an inverter listed for battery storage on Synergy's list
- 14 of 15 systems
- Warranty
- 10 years · terms listed for 1 of 15 models
- Chemistry
- LFP
- Backup capable
- 1 of 15 models
Sungrow · manufacturer profile
The SBR and SBH towers and the SH hybrids they run on
Solar panel manufacturer
Updated 2 November 2026 · Checked against Sungrow's Australian warranties and datasheets, the CEC register (16 November 2026) and Synergy's list (30 October 2026) · By Solar Battery Perth
In short
Sungrow makes the SH hybrid inverters and two high-voltage home batteries. The SBR runs only on Sungrow's SH hybrids, and Sungrow's chart pairs both towers with SH hybrids only. The SBR is a tower of 3.2 kWh LFP modules (lithium iron phosphate), from 6.4 to 25.6 kWh. The SBH uses 5 kWh modules, from 15 to 40 kWh. Either tower can be added to later on a single-phase SH-RS hybrid, which is what both manuals require for adding modules. Both carry 10 years and a 70% capacity promise, with unlimited cycles for daily solar use and backup. Sungrow Australia Group Pty Ltd in North Sydney is the importer a warranty claim reaches. A battery system needs an inverter with a battery-storage (DER-Storage) listing on Synergy's Supported Solutions List to be eligible for the WA Battery Scheme. Other scheme conditions apply. Sungrow's SH5.0RS to SH10RS single-phase and SH5T to SH25T three-phase hybrids were on Synergy's list dated 30 October 2026. So were the SH5.0RT and SH10RT. An SBR or SBH on one of them pairs with an inverter listed for battery storage on Synergy's list.
Specifications and pricing change. Confirm them with the manufacturer.
The company
Sungrow was set up in Hefei, China, on 28 November 1997, and it has built solar inverters and storage from the start. Inverters are still its core product. Its shares have traded on the Shenzhen Stock Exchange since November 2011, under the code 300274. At the end of 2025 it had 19,006 staff, and about 40% of them, 7,625 people, worked in research and development.
By its own account, Sungrow shipped 143 GW of solar inverters and 43 GWh of storage worldwide in 2025. It also says it sells in more than 100 countries, with more than 20 overseas branches and more than 520 service outlets.
In Australia, Sungrow Australia Group Pty Ltd in North Sydney is a wholly owned subsidiary. It is the importer named on the battery warranty. It has an 1800 service line and a service email, and a claim starts with the installer and is lodged with it online. Sungrow's Australian site has carried an SBR safety data sheet since March 2021, and the sheet was issued in November 2020.
A claim starts with your installer, and it is lodged online with Sungrow Australia. Sungrow then sends replacement parts, or an equivalent new or refurbished unit, by standard freight.
From Sungrow's Australian battery warranty, version 9.0, and its Australian product pages, read 8 October 2026.
The batteries and the hybrids are one system. The SBR manual says it connects only to Sungrow's SH hybrids, and Sungrow's cross-reference chart sets out which tower goes with which inverter. So the installer picks the pairing from Sungrow's own table, and the quote carries both codes.
The warranty puts no cycle cap on everyday use. For daily solar self-consumption and backup, the cycles are unlimited for the full 10 years. An energy cap applies only to other uses. That is a different shape from the usual throughput allowance, and it matters when the battery joins a program that cycles it harder.
Backup is fast on paper. Every SH hybrid datasheet we read moves the backup circuits onto the battery in under 10 milliseconds. The bigger SBH can also push a lot of power: 10.56 kW from three modules and 28.16 kW from eight, before the inverter's own limit applies.
On the Clean Energy Council (CEC) register, the SBR064 to SBR256 sit on a certificate approved on 2 August 2023, and the SBH100 to SBH400 on one approved on 4 January 2024. On the register dated 20 October 2026, the SBR certificate runs to 30 November 2026 and the SBH certificate to 4 January 2027. No Sungrow product was on the CEC's de-listing or suspension tables when we read them. The SH hybrids on the register are the single-phase SH5.0RS, SH6.0RS, SH8.0RS and SH10RS, and the three-phase SH5T to SH25T, SH5.0RT and SH10RT. Sungrow's SG string inverters and CX commercial units are listed too, and they are not part of a home battery system. Sungrow's SH5.0RS to SH10RS single-phase and SH5T to SH25T three-phase hybrids were on Synergy's list dated 30 October 2026. So were the SH5.0RT and SH10RT. An SBR or SBH on one of them pairs with an inverter listed for battery storage on Synergy's list.
2 to 8 modules of 3.2 kWh, 6.4 to 25.6 kWh usable, 33 kg a module, IP55, on the floor and fixed to the wall, indoors or out
CEC approved
Modules of 5.0 kWh, 45 kg a module, IP55, on the floor and bracketed to the wall, indoors or out
Standalone battery, on a separate inverter. On the CEC register: 10 to 40 kWh usable, in 5 kWh steps (2 to 8 modules)
CEC approved
SH5.0RS to SH10RS, backup output 5 to just under 10 kW, switch under 10 milliseconds, IP65; consult Sungrow before an outdoor install within 500 m of the coast
CEC approved
SH5T to SH25T, backup output 5 to 25 kW, switch under 10 milliseconds, IP65; consult Sungrow before an outdoor install within 500 m of the coast
CEC approved
SH5.0RT and SH10RT, on the register and the pairing chart; no datasheet read for this page
CEC approved
The SBR is a tower of 3.2 kWh LFP modules, two to eight high, from 6.4 to 25.6 kWh usable, and Sungrow's manual has it fixed to the wall. Each module is 33 kg, so the smallest tower weighs 89 kg and the largest 279 kg.
The tower's output grows with its height. The datasheet rates the SBR064 at 3.84 kW and the SBR256 at 15.36 kW, with 30 A of continuous charge and discharge throughout. A small tower only supplies its own rated kilowatts, and the inverter draws the rest from the panels. Up to four equal towers can share one hybrid, which adds capacity without raising voltage or current.
It charges between 0 and 50 °C and discharges down to -20 °C. The enclosure is rated IP55, which is dust-protected and protected against water jets, and the datasheet allows it indoors or outdoors. It is made in China.
The SBH is the same idea with bigger modules: 5 kWh each, three to eight high, for 15 to 40 kWh usable. A module is 45 kg, so a three-module SBH150 weighs 151 kg and an eight-module SBH400 weighs 376 kg. Up to four SBH units can run in parallel, to a ceiling of 160 kWh.
It moves more power than the SBR. The datasheet rates the SBH150 at 10.56 kW and the SBH400 at 28.16 kW, at 50 A of continuous charge and discharge. Those figures fall with heat and with a low state of charge, and the hybrid caps them anyway. It runs in the same 0 to 50 °C charging range as the SBR, is rated IP55, and goes indoors or outdoors on a floor. Sungrow's SBH manual places it close to the wall with a fixing bracket so it cannot tip over.
Sungrow's own chart decides it. The SBR connects only to Sungrow hybrids. The largest SBR256 is not permitted on the single-phase SH5.0RS to SH10RS, because it exceeds their voltage range. The smallest SBR064 is not permitted on the three-phase SH5.0RT, SH10RT or SH5T to SH25T, because it sits below their start-up voltage. Everything in between pairs with both.
For the SBH, the single-phase SH5.0RS to SH10RS take the SBH150 to SBH300. The SBH350 and SBH400 exceed their voltage range. The three-phase SH5T to SH25T take all six sizes, and the SH5.0RT and SH10RT take up to the SBH350.
The hybrid then sets the power the home can draw. The SH5.0RS charges and discharges at 6.6 kW and gives 5 kW of backup. The SH10RS runs at 10 kW with just under 10 kW of backup. On three phases, the SH5T charges at 15 kW, discharges at 5 kW and backs up 5 kW. The SH25T runs at 30 kW charge, 25 kW discharge and 25 kW backup. All four switch to backup in under 10 milliseconds, are rated IP65, and run from -25 to 60 °C. The SH3.0-6.0RS manual asks for a sheltered spot, out of direct sun and severe weather, and strictly prohibits installing on combustible building materials. All three SH manuals ask installers to consult Sungrow before an outdoor install within 500 metres of the coast.
The SH hybrids carry their own warranty: 10 years from installation, and at most 11 years from manufacture. It transfers with the original proof of purchase, and extensions can be bought.
Both towers use LFP prismatic cells. The SBH manual says a fire suppression kit is built into each module and triggers in an emergency. No SBR document we read describes one. No Sungrow product was on the CEC's de-listing or suspension tables when we read them.
Sungrow's Australian battery warranty, version 9.0, covers batteries installed from 21 May 2026. It runs 10 years from installation, or 126 months from manufacture, whichever comes first. At 10 years the battery still holds at least 70% of its starting capacity. For daily solar use and backup, the cycles are unlimited. Ten years is also the term the federal energy department says many battery makers offer.
Any other use, or a mix that includes one, falls under an energy cap instead. The cap runs from 17.92 MWh (megawatt-hours) on the SBR064 to 71.68 MWh on the SBR256, and from 42.00 MWh on the SBH150 to 112.00 MWh on the SBH400. That is 2.8 MWh for each kWh of nominal capacity, which a battery cycled fully every day uses up in about 7.7 years. The terms do not mention virtual power plant use, so a home joining one should ask Sungrow in writing which column applies.
Version 9.0 adds a heat rule that Perth buyers should read twice. The capacity promise applies where, each year, the battery sees fewer than 90 days between 35 and 40 °C and fewer than 30 days above 40 °C. The rest of the year has to average below 25 °C. Outside that profile, the capacity and energy cover may not apply. Batteries installed between 1 October 2024 and 20 May 2026 sit under version 8.0, which carries the same 10 years and 70% without the heat profile. A shaded, ventilated spot is the practical answer.
Four conditions matter most. The battery is monitored in iSolarCloud, Sungrow's platform. A battery not monitored there is excluded. Where its performance data is incomplete, deleted or altered, Sungrow honours the warranty for at least 4 years from installation. Running outside -20 to 50 °C is excluded. Moving the battery to a location other than where it was first installed without Sungrow's written consent is excluded. And the warranty goes to the original purchaser, or the end user an installer supplies. It does not otherwise transfer.
Adding to a tower later is allowed on an SH-RS hybrid, with a catch. The capacity promise on new modules runs from the original install date, or from the oldest module's build date. It does not start on the day they go in. A whole new tower added on site counts as a new battery and is registered on its own.
A claim goes to the installer first and is lodged online with Sungrow Australia. Sungrow sends replacement parts, or an equivalent new or refurbished unit, by standard freight. It may pay the installer a standard service rebate once the returned battery tests as defective. Travel and on-site installation costs are not covered. The warranty sits alongside your rights under the Australian Consumer Law.
The warranty answer is 10 years at 70% or better, with no cycle limit for daily solar use and backup. For other uses the energy cap of 2.8 MWh per kWh lasts about 7.7 years at one full cycle a day. The datasheets we read give no laboratory cycle rating for either tower.
Showing: Western Australia, Synergy network. Other states: not covered yet
A battery system needs an inverter with a battery-storage (DER-Storage) listing on Synergy's Supported Solutions List to be eligible for the WA Battery Scheme. Other scheme conditions apply. Sungrow's SH5.0RS to SH10RS single-phase and SH5T to SH25T three-phase hybrids were on Synergy's list dated 30 October 2026. So were the SH5.0RT and SH10RT. An SBR or SBH on one of them pairs with an inverter listed for battery storage on Synergy's list.
Synergy's list names inverters, not batteries. An SBR or SBH counts through the SH hybrid it stands beside, so the pairing your installer picks from Sungrow's chart decides which listing applies.
Sungrow's inverters on Synergy's list are not yet marked activation-ready for a Synergy VPP program (list dated 30 October 2026). The WA scheme also asks the household to join a virtual power plant (VPP). That is a program that lets a retailer call on a group of home batteries. Synergy's own VPP is Battery Rewards. The scheme also allows a VPP run by the battery supplier. Sungrow's warranty does not mention VPP use. So a Perth home joining one should ask Sungrow in writing which cover applies: the unlimited cycles or the energy cap.
For the rest of the scheme's conditions, see our WA battery rebate page. Our Synergy approved products guide explains what the list covers, and our inverter library badges each model Synergy lists for the scheme.
A Sungrow battery is an SBR or SBH tower beside a Sungrow SH hybrid, chosen from Sungrow's own pairing chart. The SBR starts smaller and the SBH runs harder, and either can be added to later on an SH-RS hybrid with the capacity promise dated from the first install. The warranty has no cycle limit for daily solar use, and from May 2026 it carries a heat profile, so the spot the installer picks matters. A battery system needs an inverter with a battery-storage (DER-Storage) listing on Synergy's Supported Solutions List to be eligible for the WA Battery Scheme. Other scheme conditions apply. Sungrow's SH5.0RS to SH10RS single-phase and SH5T to SH25T three-phase hybrids were on Synergy's list dated 30 October 2026. So were the SH5.0RT and SH10RT. An SBR or SBH on one of them pairs with an inverter listed for battery storage on Synergy's list.
Ask for the tower, its module count and the SH hybrid, each by model code. Ask your installer to show the pairing on Sungrow's chart. On the CEC register dated 20 October 2026, the SBR certificate runs to 30 November 2026 and the SBH certificate to 4 January 2027. Ask which warranty version the install date puts you under, because version 9.0 adds the heat profile.
Solar Battery Perth is independent. We're not owned by an energy retailer or a manufacturer. Installers quote the actual price.
For checking
| Warranty | 10 years on the SBR and SBH, and 10 years on the SH hybridsSungrow's Australian battery and inverter warranties |
|---|---|
| Batteries | LFP (lithium iron phosphate), 6.4-49.9 kWh usable |
| Approved now | 15 batteries and 32 inverters on the CEC (Clean Energy Council) register |
| Support in Australia | Office. Contact details |
| Local support | Yes, support handled through Australian channelsSource: Australian warranty, checked 8 Oct 2026Confirmed |
| CEC listings | 192 approved right now · 18 delistedApproved |
| Documents |
Each product type at a glance. The full lists, grouped by series, are below.
We haven't reviewed Sungrow panels in depth yet. We don't hold warranty terms or a series review for them, so confirm those with your installer. Compare panels from other brands
Pick a type to open its full list, grouped by series.
Grouped by series. Open a series for each variant, or a model for full specs.
15 CEC-approved batteries · grouped into 3 series
Based on manufacturer specifications and CEC-approved configurations. Always confirm system design with your installer.
Grouped by series. Open a series for each variant, or a model for full specs.
32 CEC-approved inverters, 18 not currently listed · grouped into 28 series
SH100CX (AS4777-2 2020)
SH10RS (AS4777-2 2020)
SH10RT (AS4777-2 2020)
SH10T (AS4777-2 2020)
SH110CX (AS4777-2 2020)
SH15T (AS4777-2 2020)
SH20T (AS4777-2 2020)
SH25T (AS4777-2 2020)
SH5T (AS4777-2 2020)
SH5K-30 (AS4777-2 2020)
Compatible batteries: SBR096, SBR128, SBR160, SBR192, SBR224, SBR256
| Battery Model | SBR096 | SBR128 | SBR160 | SBR192 | SBR224 | SBR256 |
|---|---|---|---|---|---|---|
| Charge/Discharge (kW) | 5/5 | 5/5 | 5/5 | 5/5 | 5/5 | 5/5 |
| Battery Model | SBR096 | SBR128 | SBR160 | SBR192 | SBR224 | SBR256 |
|---|---|---|---|---|---|---|
| Charge/Discharge (kW) | 5.76/5.76 | 7.68/7.68 | 8/8 | 8/8 | 8/8 | 8/8 |
| Battery Model | SBR096 | SBR128 | SBR160 | SBR192 | SBR224 | SBR256 |
|---|---|---|---|---|---|---|
| Charge/Discharge (kW) | 5.76/5.76 | 7.68/7.68 | 9.6/9.6 | 10/10 | 10/10 | 10/10 |
Understanding Power Ratings:
* DC charge/discharge power varies from AC power due to inverter efficiency. Always consult with your installer for specific system design.
Grouped by series. Open a series for each variant, or a model for full specs.
145 CEC-approved panels · showing first 50 of 145
SG-48TG2D-470 (IEC 61215-2021)
SG-48TG2D-475 (IEC 61215-2021)
SG-48TG2D-480 (IEC 61215-2021)
SG-48TG2D-X-465 (IEC 61215-2021)
SG-48TG2D-X-470 (IEC 61215-2021)
SG-48TG2D-X-475 (IEC 61215-2021)
SG-48TG2D-X-480 (IEC 61215-2021)
SG-48TG4D-440 (IEC 61215-2021)
SG-48TG4D-445 (IEC 61215-2021)
SG-48TG4D-450 (IEC 61215-2021)
SG-48TG4D-455 (IEC 61215-2021)
SG-48TG4D-460 (IEC 61215-2021)
SG-48TG4D-465 (IEC 61215-2021)
SG-48TG4D-470 (IEC 61215-2021)
SG-48TG4D-475 (IEC 61215-2021)
SG-48TG4D-480 (IEC 61215-2021)
SG-48TG4D-B-450 (IEC 61215-2021)
SG-48TG4D-B-455 (IEC 61215-2021)
SG-48TG4D-B-460 (IEC 61215-2021)
SG-48TG4D-B-465 (IEC 61215-2021)
SG-48TG4D-B-470 (IEC 61215-2021)
SG-48TG4D-B-475 (IEC 61215-2021)
SG-48TG4D-BX-460 (IEC 61215-2021)
SG-48TG4D-BX-465 (IEC 61215-2021)
SG-48TG4D-BX-470 (IEC 61215-2021)
SG-48TG4D-BX-475 (IEC 61215-2021)
SG-48TG4D-X-465 (IEC 61215-2021)
SG-48TG4D-X-470 (IEC 61215-2021)
SG-48TG4D-X-475 (IEC 61215-2021)
SG-48TG4D-X-480 (IEC 61215-2021)
SG-48TT4D-435 (IEC 61215-2021)
SG-48TT4D-440 (IEC 61215-2021)
SG-48TT4D-445 (IEC 61215-2021)
SG-48TW4D-450 (IEC 61215-2021)
SG-48TW4D-455 (IEC 61215-2021)
SG-48TW4D-460 (IEC 61215-2021)
SG-48TW4D-465 (IEC 61215-2021)
SG-48TW4D-B-450 (IEC 61215-2021)
SG-48TW4D-B-455 (IEC 61215-2021)
SG-48TW4D-B-460 (IEC 61215-2021)
SG-54TG1D-435 (IEC 61215-2021)
SG-54TG1D-440 (IEC 61215-2021)
SG-54TG1D-445 (IEC 61215-2021)
SG-54TG1D-450 (IEC 61215-2021)
SG-54TG1D-455 (IEC 61215-2021)
SG-54TG1D-B-435 (IEC 61215-2021)
SG-54TG1D-B-440 (IEC 61215-2021)
SG-54TG1D-B-445 (IEC 61215-2021)
SG-54TG1D-B-450 (IEC 61215-2021)
SG-54TG1D-B-455 (IEC 61215-2021)
What has happened to Sungrow on the CEC register.
Each block is one register event. Tap a year to see its events in the list below.
SBR Battery Series Launch
Modular high-voltage battery system launched for residential market
⚡ 20 Inverter Models Listed
Inverter range expanded to 20 CEC-approved models.
☀️ 50 Panel Models Listed
Panel range expanded to 50 CEC-approved models.
⚡ 50 Inverter Models Listed
Inverter range expanded to 50 CEC-approved models.
☀️ 100 Panel Models Listed
Panel range expanded to 100 CEC-approved models.
Yes. Both the SBR and SBH datasheets print China as the country of manufacture, and Sungrow is based in Hefei. The Australian importer is Sungrow Australia Group Pty Ltd in North Sydney.
The warranty promises at least 70% of capacity at 10 years, with unlimited cycles for daily solar use and backup. For other uses an energy cap of 2.8 MWh per kWh applies, which is about 7.7 years at one full cycle a day. From May 2026 the promise also depends on a heat profile.
Yes. An SBR takes up to eight modules and an SBH up to eight, and up to four towers can share one hybrid. Both manuals allow adding modules only with a single-phase SH-RS hybrid on current firmware. The capacity promise on added modules runs from the original installation date, and a whole new tower is registered as a new battery.
For the full warranty, yes. A battery not monitored in iSolarCloud is excluded, and where the data is incomplete Sungrow honours the warranty for at least 4 years from installation.
The datasheets allow it: both towers are rated IP55 and listed for indoor or outdoor use, charging between 0 and 50 °C. Both manuals say to keep the battery out of direct sun and rain, and the SBH manual rules out sites within 500 metres of the coast. The warranty's heat profile is the other catch. The capacity promise may not apply in a year with 30 or more days above 40 °C or 90 or more days between 35 and 40 °C. So a shaded spot matters.
Sungrow is headquartered in Hefei, China and was founded in 1997. Its products are sold in Australia through SAA-accredited installers.
Sungrow's home batteries use LFP cells. LFP (lithium iron phosphate) is the most common residential chemistry in WA for its long cycle life and stability in Perth's heat.
Solar Battery Perth lists 15 CEC-approved Sungrow battery models with specs, indicative pricing and warranty detail. Compare them against other brands to find the best fit for your Perth home.
Are you Sungrow?
Help us keep this profile up to date.
How the WA Battery Scheme works, and why eligibility follows the inverter on the quote.
What Synergy's Supported Solutions List covers, and how our inverter library shows which models are on it.
How the inverter paired with a battery sets its charge rate, discharge rate and backup power.
Who to contact first when a home battery fails, and what records to keep.
Get a quote from a member installer who covers your area. You choose whether to act on it. No obligation.
Product specifications, pricing, and availability are subject to change without notice. We make no warranties regarding product performance, longevity, or suitability for your specific needs.
Always verify specifications with the manufacturer and installer before purchase. Warranty terms are set by manufacturers and may have conditions not disclosed here. Battery performance degrades over time.