Hybrid inverter · Hopetrek Innovations · CEC approved September 2026
CEC listing: SUN-TH-HP10K-A2 (AS4777-2 2020)
A 10 kW three-phase hybrid inverter that is battery-ready.
Read from the figures on this page. No review written yet.
The numbers that matter for a home. The full datasheet is below.
Not on file: we don’t have this figure from the manufacturer’s documents yet, so we leave it blank rather than print a typical value. Ask your installer to confirm it on the quote. Seen it in a document? Tell us
Every figure on file for the Hopetrek Innovations SUN-TH-HP10K-A2, by section.
| Specification | Value |
|---|---|
| Physical | |
| IP rating | IP66 |
| Installation requirements | |
| Top clearance | 500 mm |
| Side clearance | 250 mm |
| AC breaker | 10 A |
| Cable gauge | 1.5 mm² |
| Earthing method | Permanent grounded wiring system |
| DNSP pre-approval | No |
| Estimated install time | 2 hrs |
Parsed from the manufacturer datasheet, install manual, and warranty document. Confirm against the linked PDFs before relying on a value for a quote or installation.
Get a quote from an installer sourced from the WA (Synergy/Plenti) approved list
Western Power approval is required for every grid-connected install. Under Emergency Solar Management, a new system must be remotely manageable, or take an export limit instead. Ask your installer to confirm this inverter’s ESM status.
Estimate for a full-size array on this inverter
At 5 peak sun hours a day (BOM) with a 15% system derate.
The Hopetrek Innovations SUN-TH-HP10K-A2 against the closest-power inverters from other brands.
| Specification | Hopetrek Innovations SUN-TH-HP10K-A2Hopetrek Innovations | Energizer Force 10.0HS+Energizer | Energizer Force 10.0HT+Energizer |
|---|---|---|---|
| Rated power? | 10 kW | 10 kW | 10 kW |
| Max efficiency? | Not on file | Not on file | Not on file |
| MPPT trackers? | Not on file | Not on file | Not on file |
| Phases | Three-phase | Single-phase | Three-phase |
| Type | Hybrid | Hybrid | Hybrid |
| Battery ready | Yes | Yes | Yes |
| Warranty | 10 years | Not on file | Not on file |
Specs from the CEC register and datasheet enrichment. Indicative: confirm exact figures with your installer.
This warranty covers defects for 10 years, allowing 80% capacity at year 10. Warranty void if installation is non-accredited. Claims can be made via phone or email.
AI-summarised from the manufacturer warranty document. Always confirm against the linked PDF before relying on it for a claim.
From the install manual
Showing 9 of 9. The official install manual is the authoritative source — always confirm before acting.
05criticalCall your installerOutput short circuited or over temperature detected
06criticalCall your installerOutput voltage is abnormal
07criticalOverload timeout
08criticalCall your installerBus voltage is too high
09criticalCall your installerBus soft start failed
02warningOver temperature
03warningCall your installerBattery voltage is too high
04warningCall your installerBattery voltage is too low
12warningCall your installerNTC temperature sensor failure
SUN-TH-HP8K-A2 (AS4777-2 2020)
8 kW · 3φ
SUN-TH-HP12K-A2 (AS4777-2 2020)
12 kW · 3φ
SUN-SL-HP6K-A2 (AS4777-2 2020)
6 kW · 1φ
SUN-SL-HP5K-A2 (AS4777-2 2020)
5 kW · 1φ
Get a quote from a member installer who covers your area. You choose whether to act on it. No obligation.
About this data
All inverter specifications are sourced from the CEC Approved Products Register. Specifications are provided as published by the CEC and may differ from manufacturer datasheets. Verify current specifications with the manufacturer or your installer before purchasing. Not all listed models may be currently available in Western Australia.