Hybrid inverter · Hopetrek Innovations · CEC approved September 2026
CEC listing: SUN-SL-HP6K-A2 (AS4777-2 2020)
A 6 kW single-phase hybrid inverter that is battery-ready.
Read from the figures on this page. No review written yet.
The numbers that matter for a home. The full datasheet is below.
Not on file: we don’t have this figure from the manufacturer’s documents yet, so we leave it blank rather than print a typical value. Ask your installer to confirm it on the quote. Seen it in a document? Tell us
Every figure on file for the Hopetrek Innovations SUN-SL-HP6K-A2, by section.
| Specification | Value |
|---|---|
| Physical | |
| IP rating | IP66 |
| Installation requirements | |
| Top clearance | 100 mm |
| Side clearance | 100 mm |
| AC breaker | 30 A |
| Cable gauge | 6 mm² |
| Earthing method | True Neutral |
| DNSP pre-approval | Yes |
| Estimated install time | 7 hrs |
Parsed from the manufacturer datasheet, install manual, and warranty document. Confirm against the linked PDFs before relying on a value for a quote or installation.
Get a quote from an installer sourced from the WA (Synergy/Plenti) approved list
Western Power approval is required for every grid-connected install. Under Emergency Solar Management, a new system must be remotely manageable, or take an export limit instead. Ask your installer to confirm this inverter’s ESM status.
Estimate for a full-size array on this inverter
At 5 peak sun hours a day (BOM) with a 15% system derate.
The Hopetrek Innovations SUN-SL-HP6K-A2 against the closest-power inverters from other brands.
| Specification | Hopetrek Innovations SUN-SL-HP6K-A2Hopetrek Innovations | Energizer FORCE 6.0HSEnergizer | Energizer Force 6.0HT+Energizer |
|---|---|---|---|
| Rated power? | 6 kW | 6 kW | 6 kW |
| Max efficiency? | Not on file | Not on file | Not on file |
| MPPT trackers? | Not on file | Not on file | Not on file |
| Phases | Single-phase | Single-phase | Three-phase |
| Type | Hybrid | Hybrid | Hybrid |
| Battery ready | Yes | Yes | Yes |
| Warranty | 25 years | Not on file | Not on file |
Specs from the CEC register and datasheet enrichment. Indicative: confirm exact figures with your installer.
Enphase microinverters are covered for 25 years against product defects. Damage from improper installation voids the warranty. Claims can be made directly with dealer assistance.
AI-summarised from the manufacturer warranty document. Always confirm against the linked PDF before relying on it for a claim.
From the install manual
Showing 8 of 8. The official install manual is the authoritative source — always confirm before acting.
#71criticalCall your installerOverload condition detected.
#72criticalCall your installerHigh temperature warning.
#73criticalCall your installerHigh DC ripple alarm.
#66warningCharging settings mismatch between devices in the VE.Smart Networking.
#67warningBattery temperature detection failure.
#68warningDC ripple voltage too high.
#69warningCall your installerHigh battery voltage detected.
#70warningLow battery voltage detected.
SUN-SL-HP5K-A2 (AS4777-2 2020)
5 kW · 1φ
SUN-TH-HP8K-A2 (AS4777-2 2020)
8 kW · 3φ
SUN-TH-HP10K-A2 (AS4777-2 2020)
10 kW · 3φ
SUN-TH-HP12K-A2 (AS4777-2 2020)
12 kW · 3φ
Get a quote from a member installer who covers your area. You choose whether to act on it. No obligation.
About this data
All inverter specifications are sourced from the CEC Approved Products Register. Specifications are provided as published by the CEC and may differ from manufacturer datasheets. Verify current specifications with the manufacturer or your installer before purchasing. Not all listed models may be currently available in Western Australia.