Solar inverter · Deye · CEC approved May 2025
CEC listing: SUN-20K-G05-AU (AS4777-2 2020)
A 20 kW three-phase solar inverter.
Read from the figures on this page. No review written yet.
The numbers that matter for a home. The full datasheet is below.
Every figure on file for the Deye SUN-20K-G05-AU, by section.
| Specification | Value |
|---|---|
| Efficiency | |
| Max efficiency | 98.3% |
| Physical | |
| IP rating | IP65 |
| Installation requirements | |
| Top clearance | 500 mm |
| Side clearance | 500 mm |
| AC breaker | 45 A |
| Cable gauge | 10 mm² |
| Earthing method | TN-S |
| DNSP pre-approval | Yes |
| Estimated install time | 4 hrs |
Parsed from the manufacturer datasheet, install manual, and warranty document. Confirm against the linked PDFs before relying on a value for a quote or installation.
Get a quote from an installer sourced from the WA (Synergy/Plenti) approved list
Western Power approval is required for every grid-connected install. Under Emergency Solar Management, a new system must be remotely manageable, or take an export limit instead. Ask your installer to confirm this inverter’s ESM status.
Website
au.deyeinverter.comThe Deye SUN-20K-G05-AU against the closest-power inverters from other brands.
| Specification | Afore AF20K-THAfore | Solplanet ASW020K-THSolplanet | |
|---|---|---|---|
| Rated power? | 20 kW | 20 kW | 20 kW |
| Max efficiency? | 98.3% | Not on file | Not on file |
| MPPT trackers? | Not on file | Not on file | Not on file |
| Phases | Three-phase | Three-phase | Three-phase |
| Type | Solar | Hybrid | Hybrid |
| Battery ready | No | Yes | Yes |
| Warranty | 10 years | Not on file | Not on file |
Specs from the CEC register and datasheet enrichment. Indicative: confirm exact figures with your installer.
This inverter is covered for 10 years, with important exclusions for improper installation. To claim, contact customer support.
AI-summarised from the manufacturer warranty document. Always confirm against the linked PDF before relying on it for a claim.
From the install manual
Showing 64 of 64. The official install manual is the authoritative source — always confirm before acting.
F02criticalCall your installerDC insulation impedance permanent fault
F04criticalCall your installerGround fault GFDI
F06criticalCall your installerWrite the memory error
F10criticalCall your installerAuxiliary switch power supply failure
F15criticalCall your installerAC firmware over current
F16criticalCall your installerGFCI(RCD) AC leakage current fault
F18criticalCall your installerAC over current fault of hardware
F20criticalCall your installerDC over current fault of the hardware
F22criticalCall your installerCrash stop (if there is a stop button)
F24criticalCall your installerDC insulation impedance failure
F30criticalCall your installerAC main contactor failure
F35criticalCall your installerNo AC grid
F39criticalCall your installerAC over current(one cycle)
F41criticalCall your installerAC Line W,U over voltage
F42criticalCall your installerAC Line W,U low voltage
F43criticalCall your installerAC Line V,W over voltage
F44criticalCall your installerAC Line V,W low voltage
F45criticalCall your installerAC Line U,V over voltage
F46criticalCall your installerAC Line U,V low voltage
F47criticalCall your installerAC Over frequency
F48criticalCall your installerAC lower frequency
F55criticalCall your installerDC busbar voltage is too high
F56criticalCall your installerDC busbar voltage is too low
F63criticalCall your installerARC fault
F64criticalCall your installerIGBT heat sink high temperature
F01warningDC input polarity reverse fault
F03warningDC leakage current fault
F05warningCall your installerRead the memory error
F13warningWorking mode changed/Grid mode changed
F23warningAC leakage current is transient over current
F26warningThe DC busbar is unbalanced
F31warningDC boost soft start
F57warningAC reverse irrigation
F07infoGFDI blown fuse
F08infoGFDI grounding touch failure
F09infoIGBT damaged by excessive drop voltage
F11infoAC main contactor errors
F12infoAC auxiliary contactor errors
F14infoDC firmware over current
F17infoThree phase current, over-current fault
F19infoAll hardware failure synthesis
F21infoDC leakage flow fault
F25infoDC feedback fault
F27infoDC end insulation error
F28infoInverter 1 DC high fault
F29infoAC load switch failure
F32infoInverter 2 dc high fault
F33infoAC over current
F34infoAC current over load
F36infoAC grid phase error
F37infoAC three-phase voltage unbalance failure
F38infoAC three-phase current unbalance failure
F40infoDC over current
F49infoU phase grid current DC component over current
F50infoV phase grid current DC component over current
F51infoW phase grid current DC component over current
F52infoAC inductor A,phase current DC current high
F53infoAC inductor B,phase current DC current high
F54infoAC inductor C,phase current DC current high
F58infoAC grid U over current
F59infoAC grid V over current
F60infoAC grid W over current
F61infoReactor A phase over current
F62infoReactor B phase over current
SUN-20K-SG01HP3-AU-AM2 (AS4777-2 2020)
20 kW · 3φ
SUN-20K-SG05LP3-AU-SM2 (AS4777-2 2020)
20 kW · 3φ
SUN-18K-G05-AU (AS4777-2 2020)
18 kW · 3φ
SUN-18K-SG05LP3-AU-SM2 (AS4777-2 2020)
18 kW · 3φ
SUN-16K-SG05LP3-AU-AM2 (AS4777-2 2020)
16 kW · 3φ
SUN-15K-G05-AU (AS4777-2 2020)
15 kW · 3φ
Other CEC-approved products from Deye available in Australia.
Get a quote from a member installer who covers your area. You choose whether to act on it. No obligation.
About this data
All inverter specifications are sourced from the CEC Approved Products Register. Specifications are provided as published by the CEC and may differ from manufacturer datasheets. Verify current specifications with the manufacturer or your installer before purchasing. Not all listed models may be currently available in Western Australia.