Hybrid inverter · FIMER · CEC approved September 2026
CEC listing: FIM-HY-3.3-SE-A-1PH (AS4777-2 2020)
A 3.3 kW single-phase hybrid inverter that is battery-ready.
Read from the figures on this page. No review written yet.
The numbers that matter for a home. The full datasheet is below.
Not on file: we don’t have this figure from the manufacturer’s documents yet, so we leave it blank rather than print a typical value. Ask your installer to confirm it on the quote. Seen it in a document? Tell us
Every figure on file for the FIMER FIM-HY-3.3-SE-A-1PH, by section.
| Specification | Value |
|---|---|
| Physical | |
| IP rating | IP65 |
| Installation requirements | |
| Top clearance | 70 mm |
| Side clearance | 35 mm |
| AC breaker | 16 A |
| Cable gauge | 4 mm² |
| Earthing method | TN-S |
| DNSP pre-approval | No |
| Estimated install time | 5 hrs |
Parsed from the manufacturer datasheet, install manual, and warranty document. Confirm against the linked PDFs before relying on a value for a quote or installation.
Compare quotes from installers you choose
Western Power approval is required for every grid-connected install. Under Emergency Solar Management, a new system must be remotely manageable, or take an export limit instead. Ask your installer to confirm this inverter’s ESM status.
Estimate for a full-size array on this inverter
At 5 peak sun hours a day (BOM) with a 15% system derate.
Australian office
Has local presence
Website
www.fimer.comThe FIMER FIM-HY-3.3-SE-A-1PH against the closest-power inverters from other brands.
| Specification | |||
|---|---|---|---|
| Rated power? | 3.3 kW | 3.3 kW | 3.3 kW |
| Max efficiency? | Not on file | Not on file | Not on file |
| MPPT trackers? | Not on file | Not on file | Not on file |
| Phases | Single-phase | Single-phase | Single-phase |
| Type | Hybrid | Solar | Solar |
| Battery ready | Yes | No | No |
| Warranty | 10 years | Not on file | Not on file |
Specs from the CEC register and datasheet enrichment. Indicative: confirm exact figures with your installer.
This warranty covers defects for 10 years. It excludes damage from misuse or improper installation. Claims can be made via the FIMER website.
AI-summarised from the manufacturer warranty document. Always confirm against the linked PDF before relying on it for a claim.
UNO-DM-3.3-TL-PLUS-B-Q (AS4777-2 2020)
3.3 kW · 1φ
UNO-DM-3.3-TL-PLUS-SB-Q (AS4777-2 2020)
3.3 kW · 1φ
FIM-HY-3.0-SE-A-1PH (AS4777-2 2020)
3 kW · 1φ
FIM-HY-3.6-SE-A-1PH (AS4777-2 2020)
3.6 kW · 1φ
UNO-DM-4.0-TL-PLUS-B-Q (AS4777-2 2020)
4 kW · 1φ
UNO-DM-4.0-TL-PLUS-SB-Q (AS4777-2 2020)
4 kW · 1φ
Get a quote from an installer from our network that covers your area. You choose whether to act on it. No obligation.
About this data
All inverter specifications are sourced from the CEC Approved Products Register. Specifications are provided as published by the CEC and may differ from manufacturer datasheets. Verify current specifications with the manufacturer or your installer before purchasing. Not all listed models may be currently available in Western Australia.
