Hybrid inverter · Hinen · CEC approved December 2024
CEC listing: H8000H-EU (AS4777-2 2020)
An 8 kW three-phase hybrid inverter that is battery-ready and listed for battery storage on Synergy's list.
Read from the figures on this page. No review written yet.
The numbers that matter for a home. The full datasheet is below.
Not on file: we don’t have this figure from the manufacturer’s documents yet, so we leave it blank rather than print a typical value. Ask your installer to confirm it on the quote. Seen it in a document? Tell us
Every figure on file for the Hinen H8000H-EU, by section.
| Specification | Value |
|---|---|
| Power & output | |
| Nominal power | 5.12 kW |
| DC input & MPPT | |
| MPPT trackers | 2 |
| Physical | |
| Weight | 45 kg |
| IP rating | IP65 |
| Rebate eligibility | |
| Listed for battery storage on Synergy's list | Yes |
| Installation requirements | |
| AC breaker | 30 A |
Parsed from the manufacturer datasheet, install manual, and warranty document. Confirm against the linked PDFs before relying on a value for a quote or installation.
Get a quote from an installer sourced from the WA (Synergy/Plenti) approved list
Listed for battery storage on Synergy's list. Synergy's Supported Solutions List covers inverters approved for control. A battery system needs an inverter with a battery-storage (DER-Storage) listing on this list to be eligible for the WA Battery Scheme. A listing for generation only doesn't count. Other scheme conditions apply.Western Power approval is required for every grid-connected install. Under Emergency Solar Management, a new system must be remotely manageable, or take an export limit instead. Ask your installer to confirm this inverter’s ESM status.
Estimate for a full-size array on this inverter
At 5 peak sun hours a day (BOM) with a 15% system derate.
Website
www.hinen.comThe Hinen H8000H-EU against the closest-power inverters from other brands.
| Specification | Hinen H8000H-EUHinen | Energizer Force 8.0HS+Energizer | Energizer Force 8.0HT+Energizer |
|---|---|---|---|
| Rated power? | 8 kW | 8 kW | 8 kW |
| Max efficiency? | Not on file | Not on file | Not on file |
| MPPT trackers? | 2 | Not on file | Not on file |
| Phases | Three-phase | Single-phase | Three-phase |
| Type | Hybrid | Hybrid | Hybrid |
| Battery ready | Yes | Yes | Yes |
| Warranty | 10 years | Not on file | Not on file |
Specs from the CEC register and datasheet enrichment. Indicative: confirm exact figures with your installer.
Hinen offers a 10-year warranty covering defects in materials and workmanship for specified battery systems. Exclusions include improper installation and failure to meet environmental conditions.
AI-summarised from the manufacturer warranty document. Always confirm against the linked PDF before relying on it for a claim.
From the install manual
Showing 26 of 26. The official install manual is the authoritative source — always confirm before acting.
Error 108criticalCall your installerNTC Temperature too high
Error 109criticalCall your installerBus voltage abnormal
Error 110criticalCall your installerCommunication fault
Error 113criticalCall your installerOver current protected by software
Error 114criticalCall your installerOver current protected by software
Error 116criticalCall your installerGFCI Module damage
Error 121criticalCall your installerBuck boost current abnormal
Error 123criticalCall your installerBUS balance current abnormal
Error 124criticalCall your installerDCAC soft abnormal
Error 206criticalCall your installerLeakage current too high
Error 207criticalCall your installerDCI too high
Error 208criticalCall your installerAC active Power too high
Error 210criticalCall your installerPhase difference too big
Error 300criticalCall your installerEPS OP Short Fault
Error 304criticalCall your installerEPS port voltage abnormality
Error 401criticalCall your installerThe DC input voltage is exceeding the maximum tolerable value
Error 402criticalCall your installerPV Isolation Low
Error 403criticalCall your installerThe DC input current is exceeding the maximum tolerable value
Error 500criticalCall your installerBMS Communication fault
Error 502criticalCall your installerBattery voltage low
Error 503criticalCall your installerBattery Voltage High
Error 504criticalCall your installerBattery temperature out of specified range for charge or discharge
Error 505criticalCall your installerBattery terminals reversed
Error 506criticalCall your installerBattery terminal open (only for lithium battery)
Error 508criticalCall your installerBat Relay Fault
Error 125infoThe inverter is not turned on
A10000T (AS4777-2 2020)
9.999 kW · 3φ
A10000T-E (AS4777-2 2020)
9.999 kW · 3φ
H10000H-EU (AS4777-2 2020)
10 kW · 3φ
H12000H-EU (AS4777-2 2020)
12 kW · 3φ
A15000T (AS4777-2 2020)
15 kW · 3φ
A15000T-E (AS4777-2 2020)
15 kW · 3φ
Other CEC-approved products from Hinen available in Australia.
Get a quote from a member installer who covers your area. You choose whether to act on it. No obligation.
About this data
All inverter specifications are sourced from the CEC Approved Products Register. Specifications are provided as published by the CEC and may differ from manufacturer datasheets. Verify current specifications with the manufacturer or your installer before purchasing. Not all listed models may be currently available in Western Australia.