Inverter compatibility (avoid mismatches)

A battery and an inverter work together when four checks line up: both the battery and the inverter appear on the approved lists that apply to them, the brand confirms the pairing, the inverter is listed on the Synergy Supported Solutions List (SSL) in the Synergy area, and the household is enrolled in a qualifying Virtual Power Plant (VPP) product. Miss any one of these and you can end up with hardware that runs but is locked out of a scheme, or a pairing the manufacturer does not warrant.

Run the four checks below before you sign a quote. They take minutes and they catch the mismatches that cost the most to unwind later.

What four checks confirm a battery and inverter are compatible?

  1. Approved lists, on both sides. The battery and the inverter must each appear where they are required, including the Clean Energy Council's approved-products list. A product missing from the list that applies to it cannot be used to claim the rebate or scheme it gates, even if it works electrically.
  2. The brand's own pairing guide. Some brands publish their tested pairings and the firmware version each side needs to run. Where a brand publishes one, treat it as the deciding source for that combination.
  3. SSL status in the Synergy area. Synergy's Supported Solutions List covers inverters approved for control. A battery system needs an inverter with a battery-storage (DER-Storage) listing on this list to be eligible for the WA Battery Scheme. A listing for generation only doesn't count. Other scheme conditions apply. The list covers inverters, not batteries, and a system without a listed inverter is ineligible for the rebate, Battery Rewards and the interest-free loan.
  4. VPP enrolment. The rebate is conditional on signing up to a qualifying VPP product through Synergy or an approved alternative retailer, not just on owning eligible hardware. Confirm which VPP product your installer is enrolling you in before you sign.

What is the SSL, and why does it decide your rebate?

The SSL is Synergy's register of inverters approved for control; its DER-Storage listings are the ones that meet the technical requirements for the WA Residential Battery Scheme. The same listing also gates the Battery Rewards VPP and the interest-free loan, on top of the mandatory VPP enrolment. The WA battery rebate guide sets out how the rebate amount is worked out.

Our inverter library badges each model Synergy lists for the scheme, and our battery library shows each battery's CEC listing. The brand still has to approve that specific pairing, and the quote should say which VPP product the install enrols you in.

For the full list of what qualifies and how the scheme fits together, see the Synergy approved products (SSL) guide.

Do AC-coupled retrofits change the compatibility rules?

They add a set of WA rules on top. An AC-coupled battery brings its own inverter, so it does not have to be a matched pair with your current solar inverter. But under WA's connection rules in force since 1 May 2026, adding it to an existing system is treated as an alteration, and in practice that brings whole-of-site compliance into play. To keep the rebate, VPP and loan, the setup also needs a gateway on the SSL or same-brand shared compliance between the old and new inverters; without either, export is fixed at 1.5 kW. In practice, third-party gateways have had trouble meeting the requirements and completing testing. Backup capability and power limits depend on the battery's own inverter, not on your original solar inverter. In WA, adding a battery to an existing solar system counts as an alteration and can trigger whole-of-site compliance, so compare an AC-coupled retrofit against replacing your inverter with a hybrid. For many existing systems the sound path is replacing toward a DC-coupled / hybrid-inverter setup rather than expanding an AC-coupled one, avoiding future compliance limitations.

For a new install or an inverter replacement, a hybrid inverter is the modern default: it charges the battery on DC while exporting AC, and the compatibility question becomes a single pairing between the hybrid and the battery.

The trade-off between adding an AC-coupled battery and replacing your inverter with a hybrid is a decision in itself. The AC vs DC coupled batteries comparison walks through which suits a retrofit and which suits a new build.

What should a quote name for the pairing?

The exact model codes on both the battery and the inverter. With those, our libraries show where each stands: the inverter library badges each model Synergy lists for the scheme, and the battery library shows each battery's CEC listing. Two things sit outside our data: whether the brand lists the two as a tested pairing with the firmware each requires, and which VPP product the install enrols you in. Model codes, firmware, and VPP offerings move, so a pairing that was valid last year can shift with an update. If a quote names a battery brand but is vague on the inverter or the VPP enrolment, that is the gap to close before you commit.

If you are still choosing hardware rather than checking a quote, the battery brand comparison and the budget vs premium breakdown help you shortlist inverters and batteries that are known to pair.

Skip the compatibility guesswork

Get a quote from a Perth installer and ask for the inverter by model code. Our inverter library shows which models sit on Synergy's Supported Solutions List. Prefer to narrow the hardware first? Compare inverters side by side.

Want to take the next step?

Get a quote from a member installer who covers your area. You choose whether to act on it. No obligation.

We collect these details to prepare your quote match and to share with the installer(s) we match you with. Not providing them means we can't match you. Full collection notice.

By requesting quotes you agree to be contacted by installers in our network about your enquiry. Part of WattMate Pty Ltd. No spam, opt out any time.

Where next