Hybrid inverter · MG Energy · CEC approved December 2025
CEC listing: TCI X5.0 III (AS4777-2 2020)
A 5 kW single-phase hybrid inverter that is battery-ready.
Read from the figures on this page. No review written yet.
The numbers that matter for a home. The full datasheet is below.
Not on file: we don’t have this figure from the manufacturer’s documents yet, so we leave it blank rather than print a typical value. Ask your installer to confirm it on the quote. Seen it in a document? Tell us
Every figure on file for the MG Energy TCI X5.0 III, by section.
| Specification | Value |
|---|---|
| Efficiency | |
| Max efficiency | 97.2% |
| Physical | |
| Dimensions (H×W×D) | 445 × 510 × 177 mm |
| Weight | 27 kg |
| IP rating | IP65 |
| Operating temperature | -25°C to 60°C |
| Installation requirements | |
| Top clearance | 30 mm |
| Side clearance | 20 mm |
| AC breaker | 32 A |
| Cable gauge | 8 mm² |
| Earthing method | Enclosure grounding hole or PE terminal of AC plug |
| DNSP pre-approval | Yes |
| Estimated install time | 8 hrs |
Parsed from the manufacturer datasheet, install manual, and warranty document. Confirm against the linked PDFs before relying on a value for a quote or installation.
Get a quote from an installer sourced from the WA (Synergy/Plenti) approved list
Western Power approval is required for every grid-connected install. Under Emergency Solar Management, a new system must be remotely manageable, or take an export limit instead. Ask your installer to confirm this inverter’s ESM status.
Estimate for a full-size array on this inverter
At 5 peak sun hours a day (BOM) with a 15% system derate.
The MG Energy TCI X5.0 III against the closest-power inverters from other brands.
| Specification | MG Energy TCI X5.0 IIIMG Energy | Energizer FORCE 5.0HSEnergizer | Energizer Force 5.0HT+Energizer |
|---|---|---|---|
| Rated power? | 5 kW | 5 kW | 5 kW |
| Max efficiency? | 97.2% | Not on file | Not on file |
| MPPT trackers? | Not on file | Not on file | Not on file |
| Phases | Single-phase | Single-phase | Three-phase |
| Type | Hybrid | Hybrid | Hybrid |
| Battery ready | Yes | Yes | Yes |
| Warranty | Not on file | Not on file | Not on file |
Specs from the CEC register and datasheet enrichment. Indicative: confirm exact figures with your installer.
Warranty summary
This inverter has a limited warranty covering defects and failure for 0 years. It excludes non-accredited installations. Claims can be initiated through the provided contact points.
This inverter has a limited warranty covering defects and failure for 0 years. It excludes non-accredited installations. Claims can be initiated through the provided contact points.
AI-summarised from the manufacturer warranty document. Always confirm against the linked PDF before relying on it for a claim.
From the install manual
Showing 9 of 9. The official install manual is the authoritative source — always confirm before acting.
E09criticalCall your installerNo Grid
E30criticalCall your installerSolar 1 High (DC Voltage High)
E31criticalCall your installerSolar 2 High (DC Voltage High)
E34criticalCall your installerInsulation (Insulation Fault)
E01warningCall your installerAC Frequency High
E02warningCall your installerAC Frequency Low
E07warningCall your installerGrid Quality
E10warningCall your installerAC Voltage Low
E11warningCall your installerAC Voltage High
Other CEC-approved products from MG Energy available in Australia.
Get a quote from a member installer who covers your area. You choose whether to act on it. No obligation.
About this data
All inverter specifications are sourced from the CEC Approved Products Register. Specifications are provided as published by the CEC and may differ from manufacturer datasheets. Verify current specifications with the manufacturer or your installer before purchasing. Not all listed models may be currently available in Western Australia.