Hybrid inverter · SolaX Power · CEC approved May 2026
CEC listing: X3-HYB-5.0-P (AS4777-2 2020)
A 5 kW three-phase hybrid inverter that is battery-ready and listed for battery storage on Synergy's list.
Read from the figures on this page. No review written yet.
The numbers that matter for a home. The full datasheet is below.
Not on file: we don’t have this figure from the manufacturer’s documents yet, so we leave it blank rather than print a typical value. Ask your installer to confirm it on the quote. Seen it in a document? Tell us
Every figure on file for the SolaX Power X3-HYB-5.0-P, by section.
| Specification | Value |
|---|---|
| Physical | |
| IP rating | IP65 |
| Rebate eligibility | |
| Listed for battery storage on Synergy's list | Yes |
| Installation requirements | |
| Top clearance | 120 mm |
| Side clearance | 300 mm |
| AC breaker | 20 A |
| Cable gauge | 4 mm² |
| Earthing method | TN-S |
| DNSP pre-approval | No |
| Estimated install time | 2 hrs |
Parsed from the manufacturer datasheet, install manual, and warranty document. Confirm against the linked PDFs before relying on a value for a quote or installation.
Get a quote from an installer sourced from the WA (Synergy/Plenti) approved list
Listed for battery storage on Synergy's list. Synergy's Supported Solutions List covers inverters approved for control. A battery system needs an inverter with a battery-storage (DER-Storage) listing on this list to be eligible for the WA Battery Scheme. A listing for generation only doesn't count. Other scheme conditions apply.Western Power approval is required for every grid-connected install. Under Emergency Solar Management, a new system must be remotely manageable, or take an export limit instead. Ask your installer to confirm this inverter’s ESM status.
Estimate for a full-size array on this inverter
At 5 peak sun hours a day (BOM) with a 15% system derate.
The SolaX Power X3-HYB-5.0-P against the closest-power inverters from other brands.
| Specification | SolaX Power X3-HYB-5.0-PSolaX Power | Energizer FORCE 5.0HSEnergizer | Energizer Force 5.0HT+Energizer |
|---|---|---|---|
| Rated power? | 5 kW | 5 kW | 5 kW |
| Max efficiency? | Not on file | Not on file | Not on file |
| MPPT trackers? | Not on file | Not on file | Not on file |
| Phases | Three-phase | Single-phase | Three-phase |
| Type | Hybrid | Hybrid | Hybrid |
| Battery ready | Yes | Yes | Yes |
| Warranty | 10 years | Not on file | Not on file |
Specs from the CEC register and datasheet enrichment. Indicative: confirm exact figures with your installer.
This warranty covers defects for 10 years, allowing two transfers. It excludes damage from unauthorized modifications. Claims can be made via the customer support contact information provided.
AI-summarised from the manufacturer warranty document. Always confirm against the linked PDF before relying on it for a claim.
From the install manual
Showing 73 of 73. The official install manual is the authoritative source — always confirm before acting.
BE01criticalCall your installerBMS_Exter_Err
BE02criticalCall your installerBMS_InterErr
BE03criticalCall your installerBMS_OverVolt
BE04criticalCall your installerBMS_LowerVolt
BE05criticalCall your installerBMS_ChargeOCP
BE06criticalCall your installerDischargeOCP
BE07criticalCall your installerBMS_TemHigh
BE08criticalCall your installerBMS_TempLow
BE09criticalCall your installerCellImbalance
BE10criticalCall your installerBMS_Hardware
BE11criticalCall your installerBMS_Circuit
BE12criticalCall your installerBMS_ISO_Fault
BE13criticalCall your installerBMS_VolSen
BE14criticalCall your installerBMS_TempSen
BE15criticalCall your installerBMS_CurSen
BE16criticalCall your installerBMS_Relay
BE17criticalCall your installerTypeUnmatch
BE18criticalCall your installerVer Unmatch
BE19criticalCall your installerMFR Unmatch
BE20criticalCall your installerSW Unmatch
BE21criticalCall your installerM&S Unmatch
BE22criticalCall your installerCR NORespond
BE23criticalCall your installerBMS_SW Protect
BE24criticalCall your installerBMS_536 Fault
BE25criticalCall your installerBMS_SelfCheck
BE26criticalCall your installerBMS_Tempdiff
BE27criticalCall your installerBMS_BreakFault
BE28criticalCall your installerBMS_FlashFault
BE29criticalCall your installerBMS_Precharge
BE30criticalCall your installerAirSwitchBreaker
IE01criticalCall your installerTZ Protect Fault
IE02criticalCall your installerGrid Lost Fault
IE03criticalCall your installerGrid Volt Fault
IE04criticalCall your installerGrid Freq Fault
IE05criticalCall your installerPV Volt Fault
IE06criticalCall your installerBus Volt Fault
IE07criticalCall your installerBat Volt Fault
IE09criticalCall your installerDCI OCP Fault
IE10criticalCall your installerDCV OVP Fault
IE101criticalCall your installerPower Type Fault
IE103criticalCall your installerMgr EEPROM Fault
IE11criticalCall your installerSW OCP Fault
IE110criticalCall your installerBypass Relay Fault
IE111criticalCall your installerARM Para Com Fault
IE12criticalCall your installerRC OCP Fault
IE13criticalCall your installerIsolation Fault
IE15criticalCall your installerBat Con Dir Fault
IE16criticalCall your installerEPS Overload Fault
IE17criticalCall your installerOverload Fault
IE19criticalCall your installerBMS Lost
IE25criticalCall your installerInterCom Fault
IE26criticalCall your installerINV EEPROM Fault
IE27criticalCall your installerRCD Fault
IE28criticalCall your installerGrid Relay Fault
IE29criticalCall your installerEPS(Off-grid) Relay Fault
IE30criticalCall your installerPV ConnDir Fault
IE31criticalCall your installerBattery Relay Fault
IE32criticalCall your installerEarth Relay Fault
IE33criticalCall your installerParallel Fault
IE08warningCall your installerAC10mins Volt
IE102warningCall your installerPort OC Warning
IE105warningCall your installerNTC Sample Invalid
IE106warningCall your installerBat Temp Low
IE107warningCall your installerBat Temp High
IE109warningCall your installerMeter Fault
IE112warningCall your installerFAN1 Fault
IE113warningCall your installerFAN2 Fault
IE14warningCall your installerTemp Over Fault
IE18warningCall your installerBatPowerLow
IE20warningCall your installerFan Fault
IE21warningCall your installerLow Temp Fault
IE36warningCall your installerHard Limit Fault
IE37warningCall your installerCT Meter Con Fault
X3-Hybrid-5.0-D (AS4777-2 2020)
4.999 kW · 3φ
X3-IES-5K (AS4777-2 2020)
4.999 kW · 3φ
X3-MIC-5K-G2 (AS4777-2 2020)
4.999 kW · 3φ
X3-HYB-4.0-P (AS4777-2 2020)
4 kW · 3φ
X3-MIC-4K-G2 (AS4777-2 2020)
4 kW · 3φ
X3-HYB-6.0-P (AS4777-2 2020)
6 kW · 3φ
Other CEC-approved products from SolaX Power available in Australia.
Get a quote from a member installer who covers your area. You choose whether to act on it. No obligation.
About this data
All inverter specifications are sourced from the CEC Approved Products Register. Specifications are provided as published by the CEC and may differ from manufacturer datasheets. Verify current specifications with the manufacturer or your installer before purchasing. Not all listed models may be currently available in Western Australia.